Explore our solutions by clicking on the brand below:
Easy Peer-to-Peer Communication Using i2o® Technology
This graphic has many Busworks NT, BusWorks XT, BusWorks 900EN, and EtherStax I/O modules that have the ability to operate like a long-distance transmitter using i2o technology. Reproduce your sensor inputs at Point A as 4-20mA control signals at Point B. Or, monitor a discrete device at one site by reproducing the level with a relay at another location.
Use Your Existing Ethernet Lines to Save Time & Wiring Expenses
You can connect the input modules to the output modules using your existing copper/fiber infrastructure or with a single new cable. Multiple I/O modules can be multiplexed through a switch or wireless radios.
Split a Signal for Transmission to Two Different Locations
Need the input data at two remote sites simultaneously? Not a problem. i2o lets you map an input to two output modules.
No Complicated Controllers. No Software. No Programming.
Acromag’s NT, 900EN & Etherstax Ethernet I/O modules have a built-in web page making it simple to configure using your standard web browser. Just click a few menu settings, enter the IP addresses, and you are done.
Fast and easy. Acromag’s XT Ethernet I/O modules are USB configured with Acromag software. You save as a file for easy download.
Up to 12 Channels per Module Plus Reliable, Failsafe Communication
Monitor up to a dozen devices with a single pair of I/O modules. Discrete I/O modules have twelve channels that you can set up as either inputs or outputs, in four-channel groups.
Subsequently allows bi-directional communication between two modules. Analog input modules measure up to six sensor signals: either current, voltage, thermocouple, or RTD . This data is then transmitted to a six-channel analog output module providing DC current or voltage output signals.
SFS-WP – Intrinsically Safe Wireless Flow Transmitter
- Ideal when adding flow meters where there is no power– no need to run wires/conduit, installs anywhere in minutes
- Wireless data transmission anywhere in the world with an Internet connection
- Easy thread-in installation. A quick setup procedure allows you to have the unit working with just a few simple programming steps
SFT – Battery Operated Totalizer with Wireless Capabilities
- Local Display: With flow rate totalizer and diagnostics
- Long Battery Life: High-capacity Lithium battery pack powers sensors and radio for years, even in low temperatures. The transmitter can be configured for check-in intervals between 5 seconds to 1 hour to save battery life.
- Attractive ROI: Costs less than running 60 feet of wire & conduit.
- Data at Your Fingertips: Wireless data transmission anywhere in the world with an Internet connection.
- Reliable Transmission: ISM bands sustain signal strength through terrain, structures or weather for a range of up to 1/2 mile.
RT-50 Battery-Powered Flow Rate Transmitter
The RT-50 flow transmitter is a smart, versatile display that can be mounted on any turbine or gear meter. The high strength, weather-tight Polycarbonate housing can withstand the beatings of the industrial market. The digital display offers a variety of screens, including Rate, Total, Grand Total, Status, and more.
Standard on all units is Bluetooth connectivity to give you the power of programming and real-time flow monitoring anytime/anywhere from your mobile device. The easy thread-in installation and quick setup procedure allow you to be up and running quickly.
- Multiple Power Options; Battery, Loop, DC
- Backlit LCD Display
- Rate and Totalization
- Bluetooth
- Linearizer for additional accuracy
- Frequency and 4-20 mA outputs
- 2 optoisolated limit switches
Reliable and innovative Industrial Networking Solutions to keep data moving in harsh application environments. Antaira’s cutting-edge industrial networking equipment ranges from Ethernet Switches and Media Converters to Industrial Wireless and Serial Communication devices. Antaira’s products support industry standards and perform efficiently in rugged environments.
Industrial Switches
Antaira offers a variety of Industrial Ethernet switches that can perform efficiently in adverse weather conditions and environments. Set up a reliable Ethernet infrastructure that features extended temperature tolerances and enclosures designed for the roughest environments. Markets include automation processes, smart transportation systems, security operations, and power/utility plants.
Industrial Wireless Solutions
Antaira offers a variety of Industrial IEEE 802.11 a/b/g/n wireless AP/bridge/client products that deliver reliable performance across harsh weather and environmental conditions. Devices are resistant to electromagnetic disturbances, periods of voltage instability, extreme temperature fluctuations, as well as intense shock and vibration.
Markets such as oil/gas, power/utility, transportation, security and automation utilize Antaira products for their unmatched reliability and performance. We offer advanced security features suitable for high-speed performance in demanding applications.
Industrial Wireless Routers
Industrial Wireless Routers allow users to implement encrypted VPN tunnels and other basic WiFi routing capabilities for remote harsh environment applications. Our industrial WiFi routers provide vital networking capabilities for your WLAN, ranging from affordable entry-level routers to high-end, dual-radio access points/clients/bridges/repeaters with router capabilities.
With industrial wireless routers from Antaira, you can build a reliable, high-quality WLAN in virtually any environmental or industrial condition.
Antaira’s industrial serial to wireless devices easily allows an RS232 or RS422/485 device to communicate wirelessly to the network.
Industrial 802.11AC Wireless (Wi-Fi) LAN Bridge
Antaira’s AMY-5133-AC-PD is a simple point-to-point or point-to-multipoint IEEE 802.11 radio with a gigabit PoE wired interface. The Gigabit Ethernet IEEE 802.3af/at interface provides a means to power and deliver data making setup simple and clean. Alternatively, an external power supply may also be used to power the device, power supply sold separately.
Switches on the device make it possible to set up a bridging pair without having to access the software for simple solutions. This product is ideal for applications where a quick and simple wireless bridge is required.
- High-speed WLAN Supports Up to 867Mbps
- Supports 802.11AC
- MIMO Wireless Solution (Dual 2Tx/2Rx)
- PD (Powered Device) IEEE 802.3af/at Compliant or external power
- Supports Ethernet Gigabit WAN/LAN Port
- Qualcomm QCA9563+QCA9886+QCA8334
- Up to 24dBm Tx Power
- Built-in 14dBi MIMO Panel Antenna
- Operating Temperature: -30°C to 45°C
- 2-Year Warranty
WEP5: The first IoT mechanical safety pressure gauge
The right choice when industry grade wireless pressure measurement and monitoring is required provides wireless pressure measurements in a reliable and flexible manner. Integrated LoRaWAN® communication allows for long-range, low-power wireless data communication with excellent interference immunity, even in demanding industrial conditions. Together with commercially available gateways and a cloud-based web portal you can get a complete remote monitoring system up and running in just minutes.
Bourdon® configurable pressure gauges are simple to setup even for replacement or temporary installations. Hence it is a very cost-efficient way to get more data for better preventive maintenance, problem diagnostics and process monitoring.
- For corrosive gasses and liquids
- Wetted parts: Stainless steel
- Damping fluid available for applications with pulsations or vibrations
- Case material 1.4404 (316L) for aggressive atmosphere
- Long range wireless LoRaWAN communication protocol
- Remotely configurable data transfer interval
- Remotely configurable low/high threshold and high/low trend alarms
Series WTP Wireless Temperature Sensors
The Series WTP Wireless Temperature Sensors can be quickly installed on chilled water lines, air ducts or outside a building without having to run additional wiring. By sampling the temperature measurement every 10 seconds, the 3.6 V lithium battery is able to power the unit for up to 8 years. Standard with a NEMA 4X enclosure, a reliable 418 MHz signal can carry the measurements up to 100 feet without a repeater. With the optional 900 MHz repeater, measurements can be transmitted up to 1000 feet away.
JUMO Wtrans Wireless temperature measurement for industrial applications
- For processing physical measurands of the JUMO Wtrans series
- RS485 interface with Modbus protocol
- Wireless measured value reception
- No wiring work is required due to modern wireless technology
- For max. 16 measured values per receiver
The Wtrans receiver T01 in combination with suitable Wtrans transmitters is used for mobile or stationary measurements of physical measurands. A significant reduction of the installation work is achieved due to the use of trendsetting wireless technology found in the industrial radio frequency 868.4 MHz or 915 MHz.
Cable connections are not required, the radio-based sensor technology also functions in a rough industrial environment. The supplied lambda/4 antenna with an impedance of 50 ohm can be directly screwed on or mounted externally. If the antenna holder for wall mounting with a 3 m antenna cable is used, then the open air range is 300 m. In the receiver the received measured values are converted, displayed, and are available as linear current or voltage signals [0(4) to 20 mA, 0 to 10 V] and via the digital interface RS485. All receiver outputs are galvanically isolated. A connection to higher-ranking systems (such as the plant visualization software JUMO SVS3000 or the Modbus master-compatible JUMO LOGOSCREEN nt paperless recorder) is possible via the digital interface with Modbus protocol. Operation and configuration can be performed via the keypad in conjunction with a 2-line LCD display, or with a setup program for greater convenience. This way, parameters such as filter constants, offset, alarms, and drag indicators (minimum and maximum value memory) can be set separately for each channel. For this purpose, a connector is provided on the front for a PC interface with USB/TTL converter for connecting the receiver and the PC. The receiver in the mounting rail case is intended for mounting on a DIN-rail 35 mm × 7.5 mm according to DIN EN 60715. The screw terminals for the electrical connection are located at different levels. The conductor cross section should not be bigger than 2.5 mm²
Wireless Integration
Macurco Gas Detection’s equipment collects and transmits data in real-time from a remote location to a centralized location.
The TXP-WTA can be configured in single or dual sensor configurations to allow redundant readings for critical operations or monitoring combination gases. The TXP-WTA’s smart sensors allow changing sensor types quite easily. (Aluminum and Poly Black Enclosures Available)
Macurco developed the new TracXP Wireless and Fixed Gas Transmitter product suite specifically for hazardous-location gas detection applications. The TracXP products include a comprehensive line of wired and wireless gas detection solutions to address special hazard applications including harsh industrial environments and hazardous locations. TracXP by Macurco also provides cellular and satellite options for remote toxic gas monitoring solutions in real time.
The TracXP TXP-WTA Wireless Gas Transmitter provides real-time combustible and toxic gas information for worker and operational safety in Oil & Gas, Refining, Chemical Production, Water Treatment, Food & Beverage and numerous other industrial applications. The TXP-WTA provides an Intuitive non-intrusive magnetic interface – which makes set up and programming quick and easy. The TXP-WTA can be powered via a high capacity, disposable “D” size lithium battery or in permanent installations through an optional power supply board. The new TracXP-WTA can be deployed in single or dual smart sensor configurations to allow redundant readings, improved safety in critical operations and monitoring multiple gases. The TXP-WTA wireless transmitter is available with universally acceptable 2.4GHz frequency or 900 MHz frequency.
Ovarro designs, manufactures and sells end-to-end telemetry monitoring, SCADA systems and real time business optimization software to utilities (water, oil and gas and transport), broadcast and industrial markets.
We offer full end-to-end solutions, including business optimization, SCADA software, and stand-alone products.
Ovarro solutions are able to collect, structure, present and use operational data in real time, utilizing market leading core technologies: TBox, Kingfisher and Seprol RTUs with their leading-edge performance complement our SCOPE-X Telemetry & SCADA software. We combine this with our business optimization software solutions to provide the situational governance that you need.
SEcure COMmunication Made EAsy. Imagine providing secure remote services to your customers as if you were on-site. Save time, travel costs and provide instant services simultaneously. An Internet based industrial communication solution that helps you monitor, manage and service your equipment no matter where it is located – across town or around the world.
Solutions that give you the ability to reduce costs, improve customer satisfaction and boost revenues by meeting the demands for increased uptime and data collection, all while complying with international cybersecurity standards. Third generation VPN technology enables Secomea’s IIoT solutions to be:
- Used by non-IT people
- Installed by non-IT people
- Managed by non-IT people
Introducing Setra’s Wireless Sensors
Setra’s range of automated wireless transmitters provides accurate, reliable, and easily scalable measurements and monitoring with coverage for multiple measurement points. In addition to being able to measure temperatures as low as -200°C, our wireless transmitters and probes can measure a host of other environmental factors and metrics.
Wireless transmitters monitor and record temperature, humidity, and gases such as CO2 as well as track door events. Communicating over Wi-Fi, our wireless transmitters have visual, local, and remote alarm notifications.
Wireless transmitters have secure, dependable data communication and storage both locally and in the cloud with Setra’s Continuous Environmental Monitoring Software (CEMS). Each wireless transmitter can store up to 32,000 readings, or approximately three months of data. Should you lose connection to the gateway or the cloud, there would be no loss of data. And with CEMS, users can view real-time data and receive deviation alarms as they occur.
Contact Us
Contact Davis Controls today about our state-of-the-art products and experience our expert application advice and reliable service!
CONTACT US
